Department of the interior, Department of the Car Interior, Console Supplies, 4wd Storage Drawers, Storage Drawers, car interiors, centre roof console, custom built console, floor console, roof console, overhead console, 4wd shelf
         
Asia Motors
Hino
International
Kia
Lada Niva
Landrover
Mack
MG
Morris
Oka Motors
Peugeot
Porsche
Renault
Rocsta
Saab
Ssangyong

Subaru

Suzuki
Toyota
UD
Volkswagen


       

 

You are in Products -> Nissan & Datsun -> Patrol GU Stationwagon -> Cargo Storage Drawers

The following information is specifically for the Nissan GU Patrol. See Storage Drawers for Cargo Areas for detailed information. See features, prices, optional extras, and how our drawers are constructed so that they are stronger and lighter.

Why buy our drawers?



Nissan GU Patrol cargo storage drawers displaying the optional "lift off" table that sits on the top of an open drawer.
300mm high full draw system.
300mm high single drawer unit and floor mounted fridge slide.
  
Our floor mounted fridge slide comes complete with a latch that locks the fridge slide in the open and closed positions.
ABOVE-RIGHT is an example of a single drawer unit which allows for the use of one third row passenger's seat. Single drawer units are available for the driver's side or the passenger's side. Another popular scenario is to fit a single drawer unit on one side and fit a fridge slide on the cargo floor next to the single drawer unit.

The options of a built in fridge slide, drawer partitions and "lift off" table are available for a single drawer unit.

Points of Interest:

  • Our storage drawers have been designed to be as strong and as light as possible. This is achieved by constructing the drawers from marine bonded plywood then re-enforcing any areas that are highly stressed with steel components. Some parts are glued screwed and braced, other parts are riveted or bolted together. Click here for more information on the construction.
  • Designed individually to suit the Patrol, neatly following the contours of the vehicle. Our drawers are designed to utilise all the space available.
  • Fits the vehicle without drilling any holes by utilising four seat mount captive nuts and two child restraint captive nuts in the cargo area.
  • If required, a full Milford cargo barrier can be fitted in front of this system.
  • We can build a drawer system for the Patrol at wheel arch height (250mm) or 300mm high.
  • A bed extension is also available for this model.

Full drawer system (standard height) (two drawers "side by side") $2220 + options, half drawer system (one drawer) $1110 + options.

The internal dimensions for each drawer are: 875mm(L) 460mm(W) 180mm (H). (These measurements are for our standard size drawer system. The height of each drawer can be changed to suit the customer).

Full drawer system (300mm high) (two drawers "side by side") $2300 + options, half drawer system (one drawer) $1150 + options.

The internal dimensions for the 300mm high drawers are: 875mm(L) 460mm(W) 261mm (H).

The false floor on the cargo drawers is the same height as the middle row seat when the backrest is folded down.

FITTING INSTRUCTIONS: Nissan GU Patrol (DX)

Step 1. Remove the two child restraint fittings and the four tie down assemblies (see sketch)

Step 2. The four 'seat mount' captive nuts and the two child restraint captive nuts will be utilised to mount the drawer system. Replace the threaded screws into the remaining eight captive nuts to seal off the cargo floor.

Step 3. Remove the rubber floor mat from the cargo area.

Step 4. The top of this drawer system (the false floor) is in two sections. Unscrew each of these sections and remove them from the drawer units. If the drawer system has a built in fridge slide, only remove half of the false floor - ie remove the false floor on the opposite side to the fridge slide.

Step 5. Place the drawer units in the vehicle without the false floor and the side fillers attached. Align the mounting holes in the drawer units with the six captive nuts.

Step 6. Open the fitting kit. Join the two drawer units together using the six 35mm x 6mm threaded screws, nuts and washers provided in the fitting kit - the holes are drilled (If the drawer system has a built in fridge slide there are only five threaded screws. Three 30mm x 6mm and two 35mm x 6mm).

Step 7. Fix the drawer unit into position. Firstly by replacing the two child restraint threaded screws, washers and spacers. We have supplied two additional washers. They should be placed under the captive washers on the two child restraint threaded screws. Secondly, remove the four threaded screws and washers supplied in the fitting kit and fit them to the "seat mount" captive nuts.

Step 8. Attach the two side fillers using the four countersunk head screws provided in the fitting kit.

Step 9. Place the false floor tops in position then screw them back onto the drawer units.

FITTING INSTRUCTIONS: Nissan GU Patrol ST & TI

Step 1. Remove the passenger seats in the cargo area. Remove the two child restraint fittings, the seat mounts, the seat belts and three of the four tie down assemblies (see sketch)

Step 2. The four 'seat mount' captive nuts and the two child restraint captive nuts will be utilised to mount the drawer system. Replace the threaded screws into the remaining six captive nuts to seal off the cargo floor.

Step 3. The top of this drawer system (the false floor) is in two sections. Unscrew each of these sections and remove them from the drawer units. If the drawer system has a built in fridge slide, only remove half of the false floor - ie remove the false floor on the opposite side to the fridge slide.

Step 4. Place the drawer units in the vehicle without the false floor and the side fillers attached. Align the mounting holes in the drawer units with the six captive nuts.

Step 5. Open the fitting kit. Join the two drawer units together using the six 35mm x 6mm threaded screws, nuts and washers provided in the fitting kit - the holes are drilled (If the drawer system has a built in fridge slide there are only five threaded screws. Three 30mm x 6mm and two 35mm x 6mm).

Step 6. Fix the drawer unit into position using the genuine threaded screws washers and spacers. We have supplied two additional washers. They should be placed under the captive washers on the two child restraint threaded screws.

Step 7. Attach the two side fillers using the four countersunk head screws provided in the fitting kit.

Step 8. Place the false floor tops in position then screw them back onto the drawer units.