Click here for prices of accessories and options.

Points of Interest:

• Robust construction. Suitably durable for "off road" driving. Manufactured from steel and hardwood plywood - NO PLASTIC.
• The shape of the base of the console can be custom made to suit your radio(s) and other requirements.
• Radio holes and storage openings etc. cut to suit your requirements and accessories.
• Designed for maximum headroom without interfering with the sunvisors or any other functions of the vehicle.
• Upholstered in a vinyl or velour finish.
• A vacuum formed finish is also available for this roof console. This is a foam backed, heat shrunk, one wrap (no seams) finish similar to the finish of the dashboard. For prices click here.
• Removal of the genuine spectacle / map light assembly reveals an opening in the hoodlining, our consoles have been designed to take advantage of this opening. The radio fitted into the front of the console can protrude past the top of the console, sitting in the space between the hoodlining and the turret. This design allows the console to be less intrusive and allows the front radio to sit further forward making it easier to see and operate.
• The original spectacle holder / map light assembly can be refitted to our console if required.
• Six holes must be drilled into the vehicle to fit this console. The two front mounting screws for the console are attached to the steel panel that is covered by the spectacle holder / map light assembly. The four rear mounting screws for the console are attached to the steel channel that is covered by the interior light. The interior light is remounted into a pre-cut hole in the base of the console. All wiring can be installed without drilling any holes or cutting the trim. If the console is removed and the vehicle is taken back to standard, the six holes are not seen, they are covered by the spectacle holder and the interior light.
• For mounting purposes this console comes complete with a removable speaker grill fitted to the base of the front housing.
• Designed so the radio curly cords are out of view.
• We manufacture our consoles in weekly batches. If we receive an order by Monday 5:30pm Sydney time your console will be dispatched on the following Friday. The dispatch date can vary if there is a public holiday.
• Professional fitting service available.
  

Your centre roof console will be designed to suit your specific model vehicle. It will neatly follow the contours of your hoodlining and will be the ideal width to suit the distance between your sunvisors. The length of the console takes into account the mounting system for the console, the shape of the cabin and when applicable, headroom for the rear seat passengers. When calculating the depth of the console we allow for maximum headroom and a clear view for the rear vision mirror. As no two model vehicles are the same our "vehicle specific" consoles are the best available.

In addition to being "vehicle specific" we also "custom build" each console to suit your requirements - nobody else does that! We adjust the shape of the base of the console to suit your radio(s) storage or lighting requirements. When custom building your console we can build a slim line console for maximum headroom or a deeper console for maximum storage. We can make the console's radio housing(s) as small as your radio(s) will allow providing more headroom and moving your radio(s) closer to the windscreen for better access. Another advantage of this versatility of design, most modern radios have a LCD (liquid crystal display) screen. It is easier to read the LCD when you are looking square onto the screen. Whenever possible, we change the angle on the console's facia panel to suit the radio being fitted.

Below are some sketches to show you some of the possible variations available for centre roof consoles.

FITTING INSTRUCTIONS:

Introduction. Six holes must be drilled into the vehicle to fit this console. The two front mounting screws for the console are attached to the steel panel that is covered by the spectacle holder / map light assembly. The four rear mounting screws for the console are attached to the steel turret support that is covered by the interior light. The interior light is re-mounted into a pre-cut hole in the base of the console. All wiring can be installed without drilling any holes or cutting the trim.

Step 1. Remove the spectacle holder / map light assembly and the interior light.

Step 2. Hold the console into position to check the fit. Make sure you have received the correct console, in good order, before cutting any holes in the console.

Step 3. Remove the speaker grill fitted to the front of the console.

Step 4. If you are fitting the spectacle holder / map light assembly into the console, position the assembly over the hole on the base of the console. Secure the assembly in position by running a bead of silicon around the edge of the hole on the inside of the console. The silicon must be dry before proceeding to step 5.

Step 5. Fit your radio(s) and accessories into the console - see the "instructions on installing a radio into a console" and the "radio fitting kit" supplied with the console.

Step 6. Prepare the roof console to accept the genuine interior light. Firstly, cut out the vinyl covering the hole in the plywood for the interior light. The vinyl should be cut 6mm inside the edge of the hole to allow a clear view when screwing the console into position. This hole is covered by the base of the light, cutting this hole will not effect the upholstered finish. Place the interior light on the base of the console, covering the hole. Using the two 40mm long screws and the two small washers supplied with the "console fitting kit", screw the interior light onto the console. Remove the interior light from the console to allow access to the consoles rear mounting screw holes. It is now a simple procedure to re-mount the interior light after the console is fitted.

Step 7. Install the wiring and aerial lead(s) before fitting the console. Be sure to leave enough spare wire to reach down the seat. This will make it easier to connect your wiring to the radio(s) before fitting the console. The excess wire can be coiled up inside the console.

Step 8. Place the console on the seat. Connect the wiring and check that the radio(s) and accessories are operational before installing the console.

Step 9. Make sure the interior light wire is long enough to reach past the base of the console. A gentle pull will free up some extra length of this wire. In most cases it will not be necessary to extend this wire. When fitting the console make sure you don't sandwich this wire between the console's wooden spacer and the steel turret support.

Step 10. Coil up any excess wire while lifting the console into position. Thread the interior light wire down through the hole in the console's wooden spacer. Press the console firmly onto the hood lining.

Step 12. Attach the front of the console to the vehicle using the two 75mm long screws and the two large washers provided in the fitting kit.

Step 13. Drill four 1/8" dia holes into the steel turret support for the rear mounting screws, as shown in figure 2.

Figure 2

Step 14. Attach the rear of the console to the vehicle using the four 50mm long screws provided in the fitting kit.

Step 15. Connect the interior light wiring plug then fit the interior light onto the base of the console.

Step 16. Fit the speaker grill back onto the front of the console.